Insulation Specs

7-Star Insulation Guide

Insulation is the foundation of 7-star compliance. The right R-values in the right places can make or break a NatHERS rating. This guide covers the minimum insulation specifications for walls, ceilings, and floors in every Australian climate zone, with specific adjustments for steel frame kit homes where thermal bridging reduces effective R-values.

Key principle: The R-value printed on the insulation product is the nominal rating. In a steel frame wall, the effective R-value is lower because steel studs bypass the insulation. When this guide specifies an R-value for steel frames, it refers to the batt rating you need to install — the NatHERS software will calculate the effective performance including thermal bridging.

Minimum R-Values by Climate Zone

These are practical minimums for achieving 7 stars in steel frame construction. They assume thermal breaks are installed on external steel studs. Without thermal breaks, higher batt R-values are needed (or 7 stars may not be achievable).

Wall Insulation

Climate ZoneAreasTimber FrameSteel Frame (with thermal breaks)
Zone 1Darwin, far north QLDR1.5–R2.0R2.0
Zone 2Brisbane, Cairns, coastal QLDR2.0R2.5
Zone 3Coastal NSW north, inland QLDR2.0R2.5
Zone 4Sydney, Perth, coastal NSWR2.0–R2.5R2.5
Zone 5Adelaide, inland NSW, parts WA/SAR2.5R2.5–R2.7
Zone 6Melbourne, Geelong, Ballarat, ACTR2.5R2.7–R3.0
Zone 7Hobart, Canberra, highlandsR2.5–R3.0R3.0
Zone 8Alpine areasR3.0R3.0 + external insulation

Ceiling Insulation

Climate ZoneFlat Ceiling (batts)Cathedral/Raked CeilingNotes
Zone 1R4.0R3.0Reflective foil under roofing also required
Zone 2-3R4.0–R5.0R3.0–R4.0Reflective foil helps significantly
Zone 4-5R5.0R4.0Higher is better — ceiling is the easiest win
Zone 6R5.0–R6.0R4.0–R5.0R6.0 recommended for best results
Zone 7R6.0R5.0R6.0 is standard in Hobart/Canberra
Zone 8R6.0–R7.0R5.0–R6.0Maximum practical rating for available products

Floor Insulation

Climate ZoneConcrete Slab on GroundRaised Timber/Steel FloorSlab Edge
Zone 1-3None requiredR1.0 (if enclosed subfloor)Not required
Zone 4-5Waffle pod preferredR1.5–R2.0Beneficial but not always required
Zone 6Waffle pod or edge insulationR2.0–R2.5R1.0 slab edge insulation recommended
Zone 7-8Waffle pod + edge insulationR2.5–R3.0R1.0–R1.5 slab edge insulation

These are practical guidelines for achieving 7 stars. Your NatHERS assessor will confirm exact requirements based on your specific design, orientation, glazing, and site.

Insulation Types Compared

Glasswool batts

The most common insulation in Australian homes. Available in R1.5 to R6.0 ratings for walls and ceilings. Non-combustible, affordable, and easy to install between studs. For steel frame walls, glasswool batts must be friction-fit tightly against the studs with no gaps — air gaps around the insulation dramatically reduce performance.

Rockwool (stone wool) batts

Higher density than glasswool, providing better acoustic performance alongside thermal insulation. Non-combustible and moisture resistant. Slightly more expensive but preferred in bushfire zones (BAL ratings) and where acoustic performance matters.

Rigid foam boards

Used for continuous external insulation over steel frames, slab edge insulation, and cathedral ceiling applications where cavity depth is limited. Higher R-value per millimetre than batts.

Reflective foil / sarking

Not a substitute for bulk insulation but adds R0.5 to R1.5 when installed with a still air gap. Most effective under roofing (reduces radiant heat gain by up to 97%) and on walls in hot climates. All steel frame homes should have wall sarking as a minimum for weather protection — the thermal benefit is a bonus.

Steel Frame Insulation Mistakes

Steel frame homes need more attention to insulation installation than timber frames. Common mistakes that hurt the NatHERS rating:

Insulation Budget Guide

For a 150m² single-storey steel frame kit home, typical insulation costs to achieve 7 stars:

ComponentZone 2-3 (warm)Zone 4-5 (mild)Zone 6-7 (cool)Zone 8 (alpine)
Wall batts$1,500–$2,200$1,800–$2,800$2,200–$3,500$2,800–$4,200
Ceiling batts$1,200–$1,800$1,500–$2,400$2,000–$3,000$2,400–$3,600
Floor insulation$0–$800$600–$1,500$1,200–$2,200$1,800–$3,000
Slab edge insulation—$300–$600$400–$800$500–$1,000
Sarking/wall wrap$600–$1,000$600–$1,000$600–$1,200$800–$1,400
Total insulation$3,300–$5,800$4,800–$8,300$6,400–$10,700$8,300–$13,200

These are material costs only. Installation labour adds 30–50% for ceiling and wall batts (DIY is common for owner-builders), and 50–80% for rigid board and slab edge insulation which requires more precision.

Related Guides

Insulation Specs Included with Every Kit

BRIbuild steel frame kits come with insulation schedules matched to your climate zone and confirmed by NatHERS assessment.

View Floor Plans →

Or call 1300 866 131